使Switch1的千兆端口允许所有VLAN通过的配置命令如下,请给出空白处的配置内容: Switch1(config)
使Switch1的千兆端口允许所有VLAN通过的配置命令如下,请给出空白处的配置内容:
Switch1(config)interface gigabit0/1 (进入端u配置模式)
Switch1(config-if)switchport (6)
Switch1(config-if)switchport (7) (设置封装协议为dotlq)
使Switch1的千兆端口允许所有VLAN通过的配置命令如下,请给出空白处的配置内容:
Switch1(config)interface gigabit0/1 (进入端u配置模式)
Switch1(config-if)switchport (6)
Switch1(config-if)switchport (7) (设置封装协议为dotlq)
[说明]
图4-1是在网络中划分VLAN的连接示意图。VLAN可以不考虑用户的物理位置,而
根据功能、应用等因素将用户从逻辑上划分为一个个功能相对独立的工作组,每个用户主机都连接在支持VLAN的交换机端口上,并属于某个VLAN。
[问题1](2分)
同一个VLAN中的成员可以形成一个广播域,从而实现何种功能
[问题2](2分)
在交换机中配置VLAN时,VLAN l是否需要通过命令创建为什么
[问题3](3分)
创建一个名字为v2的虚拟局域网的配置命令如下,请给出空白处的配置内容:
Switch ___(1)___(进入VLAN配置模式)
Switch(vlan) ___(2)___(创建v2并命名)
Switch(vlan) ___(3)___(完成并退出)
[问题4](2分)
使Switch l的千兆端口允许所有VLAN通过的配置命令如下,请给出空白处的配置内容:
Switch l (config)interfacegigabit0/1(进入端口6配置模式)
Switch l (config-if)switchport___(4)___
Switch l (config-if)switchport ___(5)___
[问题5](2分)
若交换机Switchl和Switch2没有千兆端口,在图4-1中能否实现VLAN Trunk的功能若能,如何实现
[问题6](2分)
将Switch l的端1216划入v2的配置命令如下,请给出空白处的配置内容:
Switch l (config)interface fastEthernet0/6(进入端口6配置模式)
Switch l (config-if)switchport ___(6)___
Switch l (config-if)switchport ___(7)___
[问题7](2分)
若网络用户的物理位置需要经常移动,应采用什么方式划分VLAN
接入层交换机Switch1的端口24为trunk口,其余各端口属于vlan11,请将(5)~(12)空缺处的内容填写完整,以完成交换机的相关配置(注:填写答案时,配置语句的关键字要求拼写完整)。
A.9 523
B.19 046
C.6400
D.12800
阅读以下说明,回答问题1~3,将答案填入对应的解答栏内。
随着越来越多的机构为任务关键型通信寻求经济利益,高可靠性变得日益关键。网络通信注意力集中在提供一种7×24小时都可用的网络架构上。可是,最大的挑战之一不是来自于网络架构,而是来自于用户级的工作站和网络设备。
热备份路由选择协议(HSRP)为IP碉络提供了容错和增强的路由选择功能。如图5-1就是一个典型的HSRP网络的实现。
两台多层交换机的配置如下,解析配置文件中部分语句的意义。
***Switch1的交换引擎的配置***
Switch1>(enable)set vtp mode server (1)
Switch1>(enable)set vtp domain Core Net //设置VTP域名
Switch1>(enable)set vlan 10 name CaiWuBu //创建VLAN 10
Switch1>(enable)set vlan 20 name XingZheng //创建VLAN 20
Switch1>(enable)set trunk 1/1 on dotlq 1-1005 (2)
Switch1 (2) (enable)set spantree root 1-40 dia 4 (3)
Switch1 (3) (enable)set spantree portfast 1/1-2 enable (4)
Switch1 (4) (enable)set spantree uplinkfast enable (5)
……(略)
***Switch1的路由引擎的配置***
Switch1(config)enable secret test //设定登录口令
Switch1(config)line vty 0 4 //进入VTY模式
Switch1(config-line)login
Switch1(config-line)password test //设用户级口令
……(略)
Switch1(config-if)interface vlan 10 //进入虚接HVLAN 10
Switch1(config-if)ip address 192.168.180.60 255.255.255.192
//设定IP地址
Switch1(config-if)no shutdown //开启端口
Switch1(config-if)standby 10 ip 192.168.180.62 (6)
Switch1(config-if)standby 10 priority 110 (7)
Switch1(config-if)standby 10 preempt (8)
Switch1(config-if)interfacevlan 20 //进入虚接口VLAN 20
Switch1(config-if)ip address 192.168.180.124 255.255.255.192
//设定IP地址
Switch1(config-if)no shutdown //开启端口
Switch1(config-if)standby 20 ip 192.168.180.126
Switch1(config-if)standby 20 priority 110
Switch1(config-if)standby 20 preempt
……(略)
***Switch2的交换引擎的配置***
Switch2>(enable)set vtp mode server
Switch2>(enable)set vtp domain Core_Net //设置VTP域名
Switch2>(enable)set vlan 10 name CaiWuBu //创建VLAN 10
Switch2>(enable)set vlan 20 name XingZheng //创建VLAN 20
Switch2>(enable)set trunk 1/1 on dotlq 1-1005
Switch2>(enable)set spantree secondary root 1-40 dia 4
……(略)
***Switch2的路由引擎的配置**+
Switch2(config)enable secret test //设定登录口令
……(略)
Switch2(config-if)interface vlan 10 //进入虚接口VLAN 10
Switch2(config-if)ip address 192.168.180.61 255.255.255.192
//设定IP地址
Switch2(config-if)no shutdown //开启端口
Switch2(config-if)standby 10 ip 192.168.180.62
Switch2(config-if)standby 10 priority 100
Switch2(config-if)standby 10 preempt
Switch2(config-if)interface vlan 20 //进入虚接口VLAN 20
Switch2(config-if)ip address 192.168.180.125 255.255.255.192
Switch2(config-if)no shutdown
Switch2(config-if)standby 20 ip 192.168.180.126
Switch2(config-if)standby 20 priority 100
Switch2(config-if)standby 20 preempt
……(略)
A.以最高可达40Gbps的速度传输数据
B.连接相机和硬盘等第三方配件
C.可连接最多两台4K显示屏或一台5K显示屏
D.以千兆速度从互联网下载文件
A.trunk 端口只能允许 1 个 VLAN通过
B.trunk 端口可以允许多个 VLAN通过
C.可以对VLAN配置描述字符串,字符串长度不限
D.通过diplay VLAN命令,可以不指定具体的VLAN,查看所有VLAN的相关信息
如图所示,一台Cisc03500系列交换机上连接2台计算机,它们分别划分在VLANl0(II)号为10)和VLANll(ID号为11)中。交换机的千兆以太网端口(go/1)连接一台路由器,使2个VLAN之问能够通信。交换机管理地址为167.11.45.2/24,缺省路由地址为167.11.45.1/24。请阅读以下交换机的配置信息,并补充【1】-【5】空白处的配置命令或参数,按题目要求完成交换机的配置(注:填写答案时,配置语句的关键字要求拼写完整)。
Switch一3548>enable
Password:***********
Switch-3548
Switch——3548configure terminal
Switch-3548(config)hostname Switch—lib
Switch—lib(config)
Switch—lib(config)interface vlan
Switch—lib(config—if)no shutdown
Swimh—lib(config—if)ip address 【1】 配置交换机管理地址
Swimh—lib(config—if)exit
Swish—lib(config)ip default—gateway 167.11.45.1
Switch—lib(config)vtp domain lib
SwiSh—lib(config)vtp mode transparent
SwiSh—lib(config)exit
Swish—libvlan data
Switch—lib(vlan)vlan 【2】 建立VLANl0
…… 建立VLANll(省略)
Switch—lib fvlan)}}exit
Switch——libconfigure terminal
Switch—lib(config)interface fO/1
Swimh—lib(config—if)no shutdown
Switch—lib(config—if)switchport【3】 为端口fO/1分配VLAN
Switch—lib(config—if)exit
Switch—lib(config)interface f0/6
…… 为端口f0/6分配VLAN(省略)
Switch—lib(config—iflexit
Switch—lib(config)interface go/1
Switch—lib(config—if)switchport 【4】 设置VLAN trunk模式
Switch—lib(config—if)switchport trunk encapsulation dotlq
Switch—lib(config—if)switchport trunk 【5】 配置允许中继的VLAN
Switch—lib(config—if)exit
Switch—lib(config)exit
Switch—lib
A、R8EGF:8端口增强千兆增强光口板
B、R4EGF:4端口增强千兆combo光口板
C、RE1XG:1端口增强10G光口板
D、SMC