OSPF network size is affected by device performance, network complexity and subnet all
A.16
B.32
C.64
D.128
A.16
B.32
C.64
D.128
A.network 10.1.1.0255.255.255.0 area0 network 192.168.1.0 255.255.255.0 area 1
B.network 10.1.1.1 255.255.255.0 area0 network 192.168.1.1 255.255.255.0 area 1
C.network 10.1.1.255 0.0.0.8 area 0 network 192.168.1.255 0.0.0.8 area 1
D.network 10.1.1.0 0.0.0.255 area 0.0.0.0 network 192.168.1.0 0.0.0.255 area 1
A.Each cell can handle the same amount of subscribers
B.The network is dimensioned for all mobile classes
C.All cells are of the same size
D.All BTSs use the same output power
E.Uplink and downlink coverage is the same
路由器R1的拓扑连接和地址分配如图7-11所示,如果在R1上安装OSPF协议,运行命令:router ospf 200,则配置E0和E1端口的命令分别是______。
A.network 10.1.1.0 255.255.255.0 area 0 network 192.168.1.0 255.255.255.0 area 1
B.network 10.1.1.1 255.255.255.0 area 0 network 192.168.1.1 255.255.255.0 area 1
C.network 10.1.1.255 0.0.0.8 area 0 network 192.168.1.255 0.0.0.8 area 1
D.network 10.1.1.0 0.0.0.255 area 0.0.0.0 network 192.168.1.0 0.0.0.255 area 1
A.nreduce size of routing table
B.nshorten route length
C.nlimit the effect of topology changes to local
D.ndecrease the quantity of LSAs and save CPU resources
A.通过network方式在Area 0内发布
B.通过import direct的方式引入到ospf中
C.不发布loopback0地址
(71)
A.numBer
B.ConneCtion
C.Diagram
D.Cost
【问题2】(6 分)
根据网络拓扑和需求说明,完成路由器R1的配置。
R1(config)# interface Serial 1/0
R1(config-if)# ip address (3) 255.255.255.0 (设置串口地址)
R1(config-if)#no shutdown (开启串口)
R1(config)#interface FastEthernet0/0
R1(config-if)#ip address (4) 255.255.255.0 (设置以太口地址)
R1(config-if)#exit
R1(config)#router ospf 1
R1(config-router)#network 192.0.0.1 (5) area 0
R1(config-router)#network 192.1.1.1 (6) area 0
根据网络拓扑和需求说明,完成路由器R1的配置。
R1 (config)# interface Serial 1/0
R1 (config-if)# ip address (3) 255.255.255..0 (设置串口地垃)
R1 (config-if) #no shutdown (开高串口)
R1 (config) #interface FastEthernet0/0
R1 (config-if) #ip address (4) 255.255.255.0 (设置以太口地址)
R1(config-if)#exit
R1(config)#router ospf 1
R1(config-router)#network 192.0.0.1 (5) area 0
R1(config-router)#network 192.1.1.1 (6) area 0
(3)
下面是路由器Router3的配置命令列表,在空白处填写合适的命令/参数,实现Router3的正确配置。
Router3>en
Router3conf term
Router3(config)interface e0
Router3(config-if)ip address (11)
Router3(config-if)end
Router3(config)router ospf 300
Router3(config-router)network (12)
【问题1】(每空1分,共11分) 公司申请到202.111.1.0/29的公有地址段,采用NAPT技术实现公司内部访问互联网的要求,其中,192.168.16.0/22网段禁止访问互联网。 R1、R2和R3的基本配置已正确配置完成,其中R1的配置如下。请根据拓扑结构,完成下列配置代码。 R1的基本配置及NAPT配置如下: R1>enable Rlconfig tenrunal R1(config)interface fastenthemet 0/0 R1(config-if)ip address 192.168.0.1 255.255.255.252 R1(config-if)no shutdown Rl(config-if)exit R1(config)interface fastenthemet 0/1 R1(config-if)ip address 192.168.0.9 255.255.255.252 R1(config-if)no shutdown R1(config-if)exit R1(config)interface fastenthernet 0/2 R1(config-if)ip address (1) 255.255.252.0 //使用网段中最后一个地址 R1(config-if)no shutdown R1(config-if)exit R1(config)interface serial 0 R1(config-if)ip address 202.111.1.1 255.255.255.248 R1(config-if)no shutdown R1(corffig)ip nat pool ss 202.111.1.1 (2) netmask (3) R1(corffig) interface (4) fastenthernet 0/0-1 R1(config-if)ip nat (5) R1(config-if)interface serial 0 Rl(config-if)ip nat (6) R1(config-if)exit R1(config)access-Iist l permit 192.168.0.0 (7) Rl(config)ip nat inside (8) list (9) pool (10) (11) 【问题2】.(每空2分,共4分) 在R1、R2和R3之间运行OSPF路由协议,其中R1、R2和R3的配置如下。 行号 配置代码 1 R1(config)router ospf 1 2 R1(config-router)network 192.168.4.0 0.0.3.255 area 0 3 Rl(config-router)network 192.168.0.0 0.0.0.3 area 0 4 Rl(config-router)network 192.168.0.8 0.0.0.3 area 0 5 R2>enable 6 R2config terminal 7 R2(config)router ospf 2 8 R2(config-router)netvrork 192.168.8.0 0.0.3.255 area 0 9 R2 (config-router)network 192.168.12.0 0.0.3.255 area 0 1 0 R2 (config-router)network 192.168.0.4 00.0.3 area 0 1 1 R3>enable 1 2 R3config terminal 1 3 R3(config)router ospf 3 1 4 R3(config-router)netvrork 192168.0.8 00.0.3 area 0 1 5 R3(config-router)network 192.168.0.4 0.0.0.3 area 0 1.配置完成后,在R1和R2上均无法ping通R3的局域网,可能的原因是(12)。 (12)备选答案: A.在R3上未宣告局域网路由 B.以上配置中第7行和第13行配置错误 C.第1行配置错误 D.R1、R2未宣告直连路由. 2.在OSPF中重分布默认路由的命令是:(13)。 (13)备选答案: A.Rldefault-informaton originate B.R1(config-if)default-information originate C.R1(config-router)default-information originate D.Rl(config)default-information originate
请阅读以下R1和R3的部分配置信息,并补充配置命令或参数,按题目要求完成路由器的配置。
R1缺省路由的配置信息:
Router-R1 configure terminal
Router-R1(config)
Router-R1(config) ip router 0.0.0.0 (6)
Router-R1(config) exit
Router-R1
R3的POS接口和OSPF协议的配置信息:
Router-R3configure terminal
Router-R3(config)
Router-R3(config) interface pos3/0
Router-R3(config-if) description To Tnternet
Router-R3(config-if) bandwidth 2500000
Router-R3(confiq-if) ip address 221.195.178.1 255.255.255.252
Router-R3(config-if) crc 32
Router-R3(config-if) pos (7)
Router-R3(COnfiq-if) no ip directed-broadcast
Router-R3(config-if) pos flag (8)
Router-R3(confiq-if) no shutdown
Router-R3(config-if) exit
Router-R3(config) router ospf 65
Router-R3(config-router) network 211.100.66.0 (9) area 0
Router-R3(config-rOuter) redistribute connected metric-type 1 subnets
Router-R3(config-router) area 0 range 211.100.66.0 (10)
Router-R3(config-router) exit
Router-R3(config)